KIT de Hardware + Full Software New Trasdata Slave 1.690€

*INCLUDES FULL SLAVE MACHINE AND SOFTWARES

Kit New Trasdata Slave Full BDM/JTAG/BOOT Reading/Programming 

INCLUDING protocols CPU

• NEW TRASDATA Lector / programmer (F34NEWTRASDATA)
• COMPLETE PACKAGE CPUs (AV99NT001)
• Power kit with international plugs (C32GNALIM12)
• Power cable with clips (F32GN003)
• DB15 adapter for reading / programming in Boot Mode of MEDC17 ECUs (F32GN037-D)
• LONG VERSION TERMINAL CABLES FOR DB15 ADAPTER (F32GN037-D-S1)
• SHORT VERSION OF TERMINAL CABLES FOR DB15 ADAPTER (F32GN037-D-S2)
• USB cable for PC / laptop connections (C32GNUSB01)
• CABLE PLANO IDC26-10 (F34NTF01)
• CABLE PLANO IDC26-14 (F34NTF02)
• CABLE PLANO IDC26-16 (F34NTF03)
• CABLE PLANO IDC26-26 (F34NTF04)
• FLAT CABLES (2) WITH FREE COLOR WIRE BDM IDC26-10 (F34NTF51)
• FLAT CABLES (2) WITH FREE COLOR CABLES JTAG IDC26-16 (F34NTF53)
• FLAT CABLES (2) WITH FREE COLOR WIRES IDC26-26 (F34NTF54)
• OBDII K/CAN2.0 Connector for New Trasdata (F34NTA14)
• Colored flat cable with flexible CAN & GPT process cables IDC26-16 (BOSCH MED17) (F34NTA15)
• DB15 cable adapter for CAN and GPT processes (BOSCH EDC17) (F32GN038)
• 1 Insulated Micro Clamp 0.025" for direct connections to the CPU pin (C34ACD013)
• Flat cable for SSM connections (password reading) for SIMOS18.x / PCR2.1 ECUs (F34NTA18)
• New Trasdata specific suitcase (ABS box with foam adapted to product shapes, K34NTVAL01)
• E-GPT specific connection wiring kit for NEW TRASDATA(K34NTA22-B)

New Trasdata is an extraordinary tool, capable of supporting the microprocessors used by all types of vehicles in the automotive field, for readings and programming in BDM, BOOT, JTAG, NBD and BAM mode.

If the vehicle control unit has "system anti-tuning" with a locked microprocessor, the New Trasdata tool performs a serial communication unlock operation restoring system operation to allow reading and programming operations through the OBDII socket with New Genius. 

It has integrated all the previous functions supported in BDM and BOOT mode, now including the following microprocessors (CPU):

• Infineon Tricore / ST Microelectronics Boot Mode (TF002 + TF003 + TF013 CPUs, also BOOT UNLOCK for OBDII programming) 
• Mitsubishi MH72xx / MH82xx Boot Mode (TF006 CPU group)
• Motorola MPC55x / MPC56x BDM Mode (TF001 CPU group)
• Motorola MC68xxx BDM Mode (TF007 CPU group)
• Motorola HC12 BDM Mode (TF008 CPU group)
• Nexus Motorola MPC55xx JTAG Mode (TF004 CPU group)
• Renesas SH7050 AUD/Boot Mode (TF005 CPU group)
• Renesas M32R Boot Mode (TF009 CPU group)
• NBD Nec 76F00xx NBD Mode (TF010 CPU group)
• Freescale/ST MPC56xx SPC56x, Freescale/ST SPC5777C, Freescale SPC577M & Infineon Aurix JTAG Mode, BAM Mode (TF011 + TF012 + TF013 CPUs)

Few and very simple steps to be operational

New Trasdata allows you to read and reprogram the entire content of the control units: microprocessor (CPU), flash Eprom and EEprom as standard. Thus, even in the event of a blockage, the control unit can be restored to its original conditions at any time (back-up). This tool also automatically performs the necessary calculations (checksum) for the correct operation of the vehicle.

A special aluminum platform and a series of specific adapters They allow all connections to be made to the control unit, without the need to make or break welding. In specific cases it is possible to carry out read/write operations without even opening the control unit.

The essential tool for reading/writing at the bank

Specific functions such as reading the complete firmware of the control unit, or the automatic identification of the engine management maps, even if they are located in several components, make the New Trasdata the reference tool on the market for reading and programming on the bench. . In specific cases it is possible to carry out read/write operations without even opening the control unit.
A single instrument available in Master and Slave versions to support all processors in the automotive field.

VER KITS DIMSPORT (New Genius + New Trasdata + Course...)

DIFFERENCES BETWEEN MASTER AND SLAVE VERSION

RECEIVE MORE INFORMATION

INTECNO DIGI TEC, S.L.

C/ Provence 339

08037 Barcelona

Tel: 902 002 151

WhatsApp: +34 663788800