Hardware New Trasdata Master-slave -KNTVER-B-

Hardware New Trasdata master and/or slave BDM/JTag/boot reading/programming

He aparato New Trasdata works only with some aggregated CPU protocol both for the version Master as Slave.

SETS UP TU NEW TRASDATA MASTER

SETS UP TU NEW TRASDATA SLAVE

USE: It is necessary to activate the tool at purchase (only once) with the product ANTMD for master, the ANTSD for slave.

NOTICE! The people/companies that buy the hardware New Trasdata and DO NOT perform the purchase/activation of any software, They wont be able dispose of the product New Trasdata, since they only work together. Please, Do not forget to purchase the desired software. (If you need help below you will see the contact numbers, thank you)

Select some kit de hardware + software in master or slave. If you need help below you have the contact numbers, thank you.

SOFTWARE ACTIVATIONS FOR NEW TRANSDATA

MASTER: 

• Activation Complete Package

• Infineon Tricore / ST Microelectronics Boot Mode (TF002 + TF003 + TF013 CPUs, also BOOT UNLOCK for OBDII programming) 

• Mitsubishi MH72xx / MH82xx Boot Mode (TF006 CPU group)

• Motorola MPC55x / MPC56x BDM Mode (TF001 CPU group)

• Motorola MC68xxx BDM Mode (TF007 CPU group)

• Motorola HC12 BDM Mode (TF008 CPU group)

• Nexus Motorola MPC55xx JTAG Mode (TF004 CPU group)

• Renesas SH7050 AUD/Boot Mode (TF005 CPU group)

• Renesas M32R Boot Mode (TF009 CPU group)

• NBD Nec 76F00xx NBD Mode (TF010 CPU group)

• Freescale/ST MPC56xx SPC56x, Freescale/ST SPC5777C, Freescale SPC577M & Infineon Aurix JTAG Mode, BAM Mode (TF011 + TF012 + TF013 CPUs)

* 1 Insulated Micro Clamp 0.025" for direct connections to the CPU pin (C34ACD013) removed from the New Trasdata Kit, must be purchased separately. 

New Trasdata is an extraordinary tool, capable of supporting the microprocessors used by all types of vehicles in the automotive field, for readings and programming in BDM, BOOT, JTAG, NBD and BAM mode.

If the vehicle control unit has "system anti-tuning" with a locked microprocessor, the New Trasdata tool performs a serial communication unlock operation restoring system operation to allow reading and programming operations through the OBDII socket with New Genius. 

Few and very simple steps to be operational

New Trasdata allows you to read and reprogram the entire content of the control units: microprocessor (CPU), flash Eprom and EEprom as standard. Thus, even in the event of a blockage, the control unit can be restored to its original conditions at any time (back-up). This tool also automatically performs the necessary calculations (checksum) for the correct operation of the vehicle.

A special aluminum platform and a series of specific adapters They allow all connections to be made to the control unit, without the need to make or break welding. In specific cases it is possible to carry out read/write operations without even opening the control unit.

The essential tool for reading/writing at the bank

Specific functions such as reading the complete firmware of the control unit, or the automatic identification of the engine management maps, even if they are located in several components, make the New Trasdata the reference tool on the market for reading and programming on the bench. . In specific cases it is possible to carry out read/write operations without even opening the control unit.
A single instrument available in Master and Slave versions to support all processors in the automotive field.

Differences between the MASTER and SLAVE versions

RECEIVE MORE INFORMATION

INTECNO DIGI TEC, S.L.

C/ Provence 339

08037 Barcelona

Tel: 902 002 151 / +34 919 993 993

WhatsApp: +34 663788800