StageX Magic Motor Sport

THURSDAY, APRIL 18, 2024

Book the power of your cars

Increase the potential of your vehicles

Tune up your beasts like PowerDivision does: major update for AI Solutions on VAG Group gasoline cars equipped with MG1 ECUs, additions for EDC16C31-equipped diesel classics and MSD8x gasoline BMWs, support for Land Rover MD1CP007, and another batch of mappacks, this time for Hitachi BED ECUs. Let's get to work!

Power your cars to the max

AI solutions for Power Division's flagship MG1CS008 ECU have arrived! A complete package of one-click solutions for Porsche , Audi , Bentley, and even Lamborghini equipped with VAG's higher-performance 4.0 TFSI engines is now easier to modify than ever before. Whether you're working on an RS6 , RS7 , Panamera , Cayenne , or even a Urus - we've got you covered.

A wide range of AI solutions ranging from Active Grille Shutter Deactivation , Catalytic Converter Deactivation , Cold Start Noise Deactivation , Gasoline Particulate Filter ( GPF/OPF ) Deactivation , Always Open Exhaust Flaps , Map Sensor Calibration , Pops&Bangs Activation , Rev Limiter Deactivation , Speed Limiter Deactivation , Start/Stop System Deactivation , to Torque Monitoring Deactivation , Evaporative Emission Control System (EVAP ) Deactivation , Variable Swirl Actuator (VSA ) Deactivation , Mid Engine Mode Deactivation , to High Pressure Fuel Pump Calibration and Secondary Air Injection (SAI ) System Deactivation are now available not only for the Power Division special but also for a wide range of Bosch ECUs such as MG1CP007 , MG1CS001 , MG1CS002 , MG1CS011 , MG1CS111 , MG1CS047 , MG1CS163 , MG1CA811. Ranging from Skoda , through Audi , to Bentley and Lamborghini , you can be sure that we have a solution for you.

Solutions for classics
Our Diesel department has been working hard to bring you something long awaited for classics. This month, we’re introducing EDC16C31 for a diverse range of cars from brands including Honda , Mitsubishi , Volvo , Toyota and Ford to our AI Solutions repertoire. Whether you need Exhaust Gas Recirculation ( EGR ) deactivation, readiness calibration, Variable Turbulence Actuator (VSA ) deactivation or Throttle Valve Actuator (TVA ) deactivation, StageX has you covered.

As if that wasn't enough, our Diesel Department has gone the extra mile to offer you something special: a complete AI Solutions package for Land Rover vehicles equipped with MD1CP007 .

Complete assistance for BMW
BMW , Alpina , and even Rolls Royce vehicles, equipped with MSD80 , MSD81 , MSD85 , or MSD87.x ECUs, are now fully supported! You can rely on solutions such as Torque Monitoring Disable , NOx Sensor Disable , Evaporative Emission Control System (EVAP ) Disable , Engine Coolant Temperature Fix , Readiness Calibration , Cold Start Noise Disable , Catalytic Converter Disable , Speed Limiter Disable , Secondary Air Injection System (SAI ) Disable , and even Pops&Bangs Activation – all accessible from a single dashboard and ready to be activated in a single click.

Mappacks for HITACHI ECUs
Last but definitely not least (!), we are very happy to announce the addition of mappacks for Hitachi ECUs to our extensive offering. Covering a range of units from BED305 , through BED434 and BED436 , up to BED501 available in a variety of cars from brands such as Alpine, Renault and Nissan , our high quality, highly detailed mappacks are designed to support your needs, whether you are aiming for Stage 1 tuning or pushing towards Stage 3. You can trust StageX to provide you with the tools you need to achieve your goals.

Wednesday, March 27, 2024

DTC Clearance Check

A whole new world of additions

Get ready to transform the way you manage DTCs and supercharge those tuning capabilities with our latest groundbreaking update! Once again, we're setting a new standard in precision, efficiency, and innovation, giving you unparalleled control over your tuning environment. Immerse yourself in a world where complexity meets simplicity and every adjustment is at your fingertips.

Here's what's new:

Cutting-edge algorithms: Our team has been working quietly behind the scenes, developing innovative algorithms tailored to every control unit we already support and a huge number of completely new units. These algorithms aren't just upgrades, but complete reinventions, ensuring the DTC removal process doesn't go astray.

Delete codes by type : From now on, you can delete codes by type! Whether it's KWP, SPN , or even manufacturer-specific codes, you can quickly and easily get rid of the ones you specify. What's more, you can even bulk delete multiple codes of different types at once.

Expansive Algorithm Extensions: The scale of this update is unprecedented . We're introducing an update to the 1,000+ already supported ECUs , along with over 100 completely new additions to our repertoire. This massive expansion not only (dramatically!) increases our coverage, but also provides a more direct and efficient way to remove the codes needed to complete your modification.

THURSDAY, MARCH 21, 2024

AI stages for MEVD17.2.x and MSD8x

We're proud to introduce a significant update to our AI tuning suite, this time focusing on Bosch MEVD17 and Siemens/Continental MSD80 gasoline ECUs for BMW, Mini, and Rolls-Royce vehicles. This update is designed to give tuners more precise, powerful, and fully customizable tuning solutions. Let's dive in!

Elevate your tuning options with advanced AI stages

Immerse yourself in our latest range of AI stages , meticulously designed for a wide range of ECUs highly demanded, including Siemens/Continental MSD80, MSD81, MSD85, MSD87 and the Bosch MEVD17.2 series, included MED17.2 , MEVD17.2 , MEVD17. 2.2 , MEVD17.2.3 , MEVD17.2.4 , MEVD17.2.5 , MEVD17.2.6 , MEVD17.2.7 , MEVD17.2.8 , MEVD17.2.9 , MEVD17.2 . G and even MEVD17.2 . h This expansion significantly expands the capabilities of StageX AI Tuning , allowing tuners to take advantage of technology cutting-edge for a wide range of vehicles classics and luxury.

BMW : Comprehensive coverage across the entire ECU spectrum, allowing tuners to optimize the power , efficiency and driving ability for almost any model .
Rolls Royce : specialized tuning for ECU MSD87, which allows tuners Refine performance while preserving the essence luxurious of the vehicle .
Mini : Specific solutions for ECUs from the MEVD17.2 series , which provide you with the tools to unlock agility and the performance in these dynamic vehicles.

Precision and personalization at the heart

At StageX, we understand that tuning It is so much an art as a science . Each vehicle is only and ours AI stages reflect it. Our software adapts improvements to each ECU and engine variant , ensuring that tuners can achieve the optimal balance between performance , reliability and driving ability . This level of customization ensures that each project of tuning can meet and even get over expectations of the client , regardless of the make or model of the vehicle. In addition, it has total flexibility for refine and further modify the AI stages , taking advantage of our map packs highly descriptive and detailed , adding an additional layer of personalization and precision to the adjustment process.

For tuners, by tuners

Developed with the knowledge and the experience of tuning professionals With decades of experience, the latest update from StageX It is designed with the perfect balance between power gross , efficiency, longevity and ease of driving . Whether you are tuning a BMW classic for the track or optimizing a Rolls Royce for get the most out of it , ours AI stages offer the precision , flexibility and the control what you need for overcome limits of what is possible in automotive tuning .

A breakthrough imminent is about to revolutionize the tuning industry once again. Stay alert and prepare to enter the next era of tuning evolution with StageX Plus, where we not only follow evolving trends, but we are at the forefront, leading the way.

WEDNESDAY, MARCH 13, 2024

Let AI do the work

Accelerate your workflow and effortlessly unleash your car's tuning potential with StageX Plus, introducing another FREE solution, this time for TCUs! Let's get started!

Free pair unlock for a wide variety of BMW equipped with 8 HP TCU ! In addition to the solutions SCR free for DCU and the solutions DPF and EGR free for various ECUs from VAG and BMW , we are pleased to introduce another free solution for all subscribers from StageX Plus , this time for transmission control units This offer extends to all BMWs F and G series, and even some E series models equipped with this TCU . These vehicles often face restrictions both in the ECU as in the TCU , so we provide a quick and easy method to remove those restrictions, giving you greater flexibility and more opportunities to power improvements with only one click .

Complete transmission control

Unlocking the full potential of your vehicle's performance isn't always just about tuning the ECU (although with our AI Stages , has never been so easy). Sometimes it also requires careful control of the transmission control unit . That's where the need to adjust the comes into play torque limiters . Some TCU have restrictions incorporated that can slow down the true power of your vehicle. To unlock the torque limiters on these TCU , we remove this barrier criticism , which allows you adjust your car above of the limits with a just click This step is essential for those seeking maximize the capabilities of the vehicle, ensuring that each modification works in harmony providing the better driving experience .

Unleash the power

As we continue to optimize the process adjustment with AI , StageX Plus is at the forefront of innovation , accelerating your workflow like never before. Our latest AI solutions , AI stages and even this new one gift are just the beginning. We are committed to providing you with the tools to unlock levels of Unprecedented performance, made easy and efficient And the best part? We're just getting started….

Something big is on the horizon, taking giant steps toward redefining what is possible in the vehicle tuning Stay tuned and ready to embrace the future of tuning with StageX Plus , where we not only keep up with the advances; we are setting the pace .

Get your promotions today!

Please note that our ongoing promotions are still available! StageX Plus subscribers can enjoy solutions DPF and EGR FREE for specific vehicles, FREE SCR for modules DCU , the recently presented gift ( Torque Unlock ) and unprecedented discounts up to 40% for everyone else.

THURSDAY, MARCH 7, 2024

Long-awaited solutions and breakthroughs

MEVD17 is just the beginning

Get ready for another impressive update: we're rolling out AI solutions for the long-awaited MEVD17 and 10JA families, and introducing a host of new options for a wide range of classic diesel engines, from Mercedes to Smart and even Chrysler. Let's explore what's new.

AI solutions for the BMW MEVD17 family

Good news for our tuning community, both professionals and enthusiasts: Petrol BMWs with Bosch MED17 and MEVD17 ECUs, including MED17.2, MEVD17.2, MEVD17.2.2, MEVD17.2.3, MEVD17.2.4, MEVD17.2.5, MEVD17.2.6, MEVD17.2.7, MEVD17.2.8, MEVD17.2.9, MEVD17.2.G and MEVD17.2.H, are now fully integrated into our AI solution suite. This expansion enriches our range of tuning capabilities, offering comprehensive services such as Catalyst Deactivation, Cold Start Noise Deactivation, Readiness Calibration, Engine Coolant Temperature Correction, Evaporative Emission Control System (EVAP) Deactivation, Torque Monitoring Deactivation, Speed Limiter Deactivation, Start/Stop System Deactivation, and the much-requested Pops & Bangs for that added aural dimension. These updates are designed to accelerate the workflow of all tuners, streamlining vehicle remapping for faster, more efficient results. Welcome to the next level of tuning excellence with our expanded AI solutions.

Unlock Alfa Romeo's potential with ease

Our AI solutions portfolio now includes Alfa Romeo cars equipped with the Marelli 10JA ECU. This addition significantly expands our tuning services . Options such as Exhaust Gas Recirculation (EGR) deactivation, Catalytic Converter deactivation, Cold Start Noise Reduction, Evaporative Emission Control (EVAP) deactivation, Speed Limiter Removal, Start/Stop Deactivation, and the much-loved Pops & Bangs for an enhanced audio experience are now within your reach. Immerse yourself in the next level of tuning sophistication with our expanded line of AI solutions .

AI solutions expand to include Mercedes and more!

Once again, we’re rolling out a massive update to our diesel AI solutions , now supporting ECUs from Bosch, Denso, and Delco . Our team has built a variety of AI solutions for you, including Diesel Particulate Filter (DPF) Deactivation, Exhaust Gas Recirculation (EGR) Deactivation, Lambda Sensor Deactivation, Readiness Calibration, Throttle Valve Actuator (TVA) Deactivation, Variable Swirl Actuator (VSA) Deactivation, and even System Activation/Stop. This update covers a variety of ECUs including Bosch EDC16C31, EDC16C32, EDC16CP31, EDC16CP36 , in addition we introduce solutions for Delco E87 and the highly sought after Denso RX703200 , supporting a wide range of vehicles from MERCEDES, TOYOTA, LEXUS, OPEL, JEEP, SMART, DODGE and CHRYSLER.

Something Big is Coming.

Get ready for an extraordinary reveal coming soon to StageX ! We're getting ready to announce something groundbreaking, and it's something you definitely don't want to miss . Be the first to know about the news; be sure to subscribe to our newsletter. Stay tuned; get ready for an announcement that will redefine gaming once again.

FRIDAY, FEBRUARY 23, 2024

Broadening the horizon with AI solutions

Stay up to date with our endless innovations

Let's dive into the latest StageX AI news: a groundbreaking update to our AI Stages for BMW and Mini vehicles, now with expanded support for diesel and gasoline engines, as well as another free SCR for DCUs, new Mappacks, and a host of new AI solutions.

Extended AI tuning for BMW and Mini

Exciting news from StageX AI: We have released a major update to our game-changing AI Stages , improving the fit experience for an even wider range of vehicles BMW and Mini This update is not just another step forward; It's a jump that expands the horizons of what is possible in car tuning , building our already monumental system.

Support has been introduced for diesel BMWs and Minis equipped with ECUs. EDC16C31 , EDC16C35 , EDC16CP35 , and advanced tuning possibilities open up for newer models that feature MD1CP002 , MD1CP032 , MD1CS001 .

But the highlight of this AI Stages update is our expansion into cars. BMW and Mini of gasoline, which include AI Stages latest generation for ECU as MG1CS003 , MG1CS024 , MG1CS049 and the exceptional MG1CS201 . This extension of the adjustment capabilities from StageX AI to gasoline engines gives you an even wider range of unparalleled performance enhancements.

Free solutions for EAS modules DCU15 and DCU17CV51

That's right: for all members from StageX Plus , new AI solutions for some trucks with submodules EAS DCU15 and DCU17CV51 are completely free. In certain vehicles, it is essential to modify both the ECU like the submodule to ensure the proper functioning of the modification of the SCR . That's exactly why, along with our ECU solutions, we also back it up with support of submodule, giving you a solution complete for SCR .
Simply set up a project for the ECU and the DCU , apply the solutions and you're all set: your files will be prepared and ready to be written to both control units.

AI solutions for the MG1 ECUs have arrived

We are pleased to announce that cars BMW and Toyota gasoline equipped with ECU from Bosch , specifically MG1CS003 and MG1CS024 , have now been added to our comprehensive set of AI solutions . Since the deactivation of the gasoline particulate filter ( GPF / OPF ), the deactivation of the catalyst , the noise deactivation from cold start, correction from the rattle of the discharge valve cold start, calibration from preparation to correction coolant temperature of the engine , deactivation of the evaporative emission control system ( EVAP ), the deactivation torque monitoring and the deactivation of the speed limiter . , the deactivation of the system Start/Stop and even the ever-popular ones Pops & Bangs for that extra auditory thrill are now available to all of you in our repertoire of AI solutions.

Major update to Delphi's AI solutions for ECUs

Once again, we bring you a huge update of AI solutions for engines diesel , this time equipped with ECU from Delphi Our team prepared for you artificial intelligence solutions such as deactivating the diesel particulate filter ( DPF ), deactivation of exhaust gas recirculation ( EGR ), the deactivation of selective catalytic reduction ( SCR ), the limitation of dosage of selective catalytic reduction ( SCR ) and deactivation of the variable turbulence actuator ( VSA ) for a variety of ECUs Delphi as DCM1.2 , DCM3.2 , DCM3.7, DCM6.2AP, DMCI, DDR and even ETC3 They are found in a variety of cars, trucks and heavy machinery from brands such as BAIC , Bobcat , CASE , CHEVROLET , DACIA , DAF , GREAT WALL , HOLDEN , HYUNDAI , Hyundai Truck , ISUZU , JAC , JCB , KENWORTH TRUCK , KIA , KING LONG , KIOTI , MAHINDRA , MERCEDES , NISSAN , NISSAN TRUCK , OPEL , PETERBILT TRUCK , RENAULT , SSANG YONG , SUZUKI , TATA , TATRA and even YOU TRUCK.

Mappacks coverage expands

In our ongoing mission to create map packs detailed and of first level for each ECU that exists, the team from Petrol Head has developed specialized map packages for the supercars of Ferrari and Maserati equipped with ECU from Bosch as ME7.3 , ME7.3.2, MED9.6.1 . In addition, we have also implemented map packs finely detailed for the models Renault and Dacia that work with ECU Siemens / Continental , as EMS3110 , EMS3125 and EMS3150 .

FRIDAY, JANUARY 12, 2024

AI Solutions Update

New tickets for StageX

Get ready for AI solutions for the long-awaited Delphi and Denso ECUs, a substantial update to our map package database, another free DCU submodule solution, and AI Stage 1 for Alfa Romeo, Fiat, and Lancia vehicles. Let's dive in!

New batch of AI Stage 1

Last month, we rolled out a full range of StageX AI capabilities , presenting the solutions of Stage 1 of AI in both StageX as in WinOLS5 Solution Manager ( F7 ).

Building on the momentum, this month we are delighted to offer you the opportunity to implement AI Stage 1 solutions. to the Marelli ECUs 8GSF , which are commonly found in a range of cars Fiat , Lancia and Alfa Romeo .
In addition, you can explore the possibilities from AI Stage 1 with Bosch MED17.3.3 which can be found in a variety of vehicles Alfa Romeo .

Be sure to explore the full list of vehicles recently admitted for AI Stage 1 next.

Map packages for MED17 and ME7 ECUs

As we continue to expand our mission of creating detailed map packages and first level for ECU around the world, our team from Petrol Head has created map packs specifically for ECU from Bosch as MED17.0 , ME7.3.1 , ME7.6.3 and ME7.9.10 .
These are found in several cars of brands such as Land Rover , Alfa Romeo , Fiat , Lancia , Abarth and even Jaguar .

AI solutions for Delphi and Denso ECUs

To start the year on a high note, our diesel department prepared artificial intelligence solutions such as deactivating the diesel particulate filter ( DPF ), deactivation of exhaust gas recirculation ( EGR ), sensor deactivation Lambda, the deactivation torque monitoring , the calibration of preparation and selective catalytic reduction ( SCR) . ) Deactivating and disabling the system Start/Stop for a variety of ECUs Delphi as DCM3.4 , DCM3.5 , DCM6.1 equipped in cars Citroen , Dacia , Nissan , Peugeot , Fiat , Ford and Toyota and engine control units Dense for Trucks HINO , identified as 89564 , RX703200 and YK71.

Additionally, in the latest update, we introduced the Selective Catalytic Reduction (SCR) deactivation AI solution ( SCR ) for the submodule DCU17CV51 found on trucks HINO equipped with the ECUs Dense mentioned above ; as always, completely FREE , at no additional charge for everyone subscribers of StageX PLUS. .

We have also welcomed gasoline ECUs Bosch ME7.6.3 and MG1CS049 , which are found respectively in cars FIAT and BMW, in our repertoire of artificial intelligence solutions , introducing deactivation of the catalyst , the deactivation of the noise of the cold start , the solution WasteGate rattle cold start, calibration of preparation and correction coolant temperature of the engine. , Deactivating the evaporative emission control system ( EVAP ), Deactivation of the gasoline particulate filter ( GPF/OPF ), Pops and explosions, Deactivating the speed limiter, Deactivating the system Start/Stop , Deactivation torque monitoring , giving you a full spectrum of possibilities with just one click!

TUESDAY, DECEMBER 19, 2023

Hundreds of new AI solutions

The StageX Christmas Festival is ramping up!

Free AI solutions until the end of the year and a massive update covering everything from passenger cars to trucks, tractors, buses, and even industrial machinery. Let's dive in!

ADVANCE IN AI TUNING

StageX AI just achieved a groundbreaking milestone: introducing Stage 1 AI solutions!

Get ready for an unparalleled tuning revolution! AI Stage 1 tuning solutions for a wide variety of car models. We're starting our lineup with BMW and Mini, where you can rely on AI Stage 1 Tuning for EDC17C06, EDC17C41, EDC17C50, EDC17C56, EDC17C76, up to EDC17CP02, EDC17CP09, EDC17CP45, up to EDC17CP49. Your tuning possibilities will soar to new heights with our state-of-the-art artificial intelligence capabilities.

True performance enhancement goes beyond the engine, so we've expanded our AI Stage 1 tuning capabilities to include transmission control units. Introducing AI Stage 1 Tuning for ZF 8HP TCUs, allowing you to upgrade your transmission in seconds. This strategic integration with your ECU tuning ensures improved performance and greater reliability. Immerse yourself in a comprehensive tuning solution, elevating your tuning experience to unprecedented heights.

Additionally, AI Stage 1 tuning options designed specifically for gasoline-powered cars with Marelli ECUs have arrived. This diverse range encompasses ECU models such as the 8GMK, 8GML, 8GMW, and 8GSW, extending up to the 10JA, which can be found in a variety of Abarth, Alfa Romeo, Dodge, Fiat, and even Jeep cars.

But how does StageX AI distinguish engine power variants? This is due to its exceptional intelligence, a feature that sets it apart in the automotive tuning field. Not only does it automatically recognize the ECU you're working with, but this advanced system goes a step further by cleverly recognizing the specific engine and its power variant.

AI SOLUTIONS ARE COMING TO TOWN

Our Diesel division has exceeded expectations this month, introducing AI solutions for a huge variety of trucks, tractors, buses, and even agricultural and industrial machinery, such as Bosch ECUs dedicated to heavy machinery, such as the EDC17CV41, EDC17CV42, EDC17CV44, EDC17CV52, EDC17CV54, and EDC17CV56.

We also welcome upcoming Denso ECUs to our AI solutions portfolio, such as 4D56, RA6, 275800, STD, F4HD, SH72546, D3, P729, 275770 for Mitsubishi, Hyundai, Kia, Nissan, Renault, or even Kubota.
In addition, we also added a solution package for a variety of Infinity and Mercedes cars with Delphi CRD3 engine control units and even expanded our support for SCR deactivation on DCU17PC42 mounted in Hyundai and Kia vehicles.

In addition, we are adding a complete package of AI solutions for BMWs equipped with MG1CS201 ECUs, now available to all StageX users, giving them a full spectrum of possibilities for their BMWs!

Gifts in WinOLS5

Until December 31st, take advantage of the StageX Plus opportunity to receive up to 5 free locked map packs on WinOLS5, every day! This exclusive offer is our way of thanking StageX users on other platforms as well.
On top of that, all active StageX Plus subscribers will enjoy free access to our state-of-the-art DTC removal algorithms in WinOLS 5, and the best part is you can benefit from this offer completely FREE up to 10 times a day!

WEDNESDAY, DECEMBER 6, 2023

StageX – Santa Claus Promotion

News under the Christmas tree.

It's time to start your engines and accelerate into the holiday spirit! We're thrilled to open the first gift (of many to come in December) for all StageX Plus subscribers.

60% off artificial intelligence solutions.

Unlock the full potential of innovation with StageX Plus while we present you an extraordinary opportunity: a whopping 60% off our next-generation AI solutions.

This exclusive offer serves as a gateway to revolutionizing your projects, providing access to cutting-edge artificial intelligence at an unbeatable price.

Expand your possibilities as you harness the power of advanced AI and enhance your efforts without compromising your budget. This 60% discount is more than just a discount; it's an invitation to explore and seamlessly integrate the latest AI technologies. However, act quickly, as this unparalleled offer is only available until December 31st. Don't miss this opportunity to supercharge your projects with StageX Plus.

60% off the regular price. This promotion cannot be combined with other offers or discounts.

Enjoy your promotions today!

Don't forget that our current promotions are still available!

StageX Plus subscribers can enjoy free DPF and EGR solutions for numerous VAG and BMW vehicles, and SCR OFF for submodules such as DCU17PC43, DCU17CV51 and DCU17HD01 is also completely free.

TUESDAY, NOVEMBER 28, 2023

StageX Advance – Closed Beta

The StageX revolutions continue

We are excited to announce the upcoming StageX Advance beta!
As we prepare for this exclusive testing phase, we invite you to be part of the action and check out the latest features and improvements.

How to join the beta:
To be among the first to experience StageX Advance, you need an active StageX Plus subscription and simply email stagex@powerdivision.com expressing your interest in the Beta—but hurry, as spaces are limited!

December 1st marks the starting line, the moment when the StageX Advance beta accelerates and enters the digital highway. It's the launch pad for 31 days of exploration, collaboration, and innovation.
As we speed through the technological landscape, the adventure concludes on December 31st, a destination where the Beta ends its journey.

So mark your calendars, tuning professionals and enthusiasts, because this road trip is about to begin, and we can't wait for you to join us on this exciting journey!

THURSDAY, NOVEMBER 9, 2023

Denso, Transtron and something free

Solutions for Denso and Transtron have arrived

AI solutions for the long-awaited Denso and Transtron ECUs, map packages and solution packs for various MED17 gasoline ECUs, another amazing FREE solution, and much more... Let's get into it!

FREE Solutions for DCU17HD01 Modules

That's right! Solutions for modules DCU17HD01 are completely FREE for all users from StageX Plus !
In some vehicles, the modification of the SCR must be done by modifying both the ECU like the submodule to work properly, that's why with the solutions introduced for the ECUs from Transtron , we also provide you with medium for your SCR submodule to provide you with a complete and reliable solution.
You just need to create projects for both control units, apply artificial intelligence solutions and you're ready to go! Your files are ready to be written to both control units.

There is nothing easier than this.

* The SCR DCU17HD01 solution is only available for cars equipped with a Transtron ECU.

AI solutions for Denso and Transtron ECUs

This month, our diesel professionals have outdone themselves and brought you artificial intelligence solutions such as deactivating the diesel particulate filter ( DPF ), deactivation of exhaust gas recirculation ( EGR ), sensor deactivation Lambda, the deactivation torque monitoring , the calibration of preparation and the deactivation of selective catalytic reduction ( SCR ). , Selective catalytic reduction dosage limitation ( SCR ), deactivation of the throttle valve actuator ( TVA ) and deactivation of the variable turbulence actuator ( VSA ), for a variety of cars Opel , Mazda and subaru with ECU Dense on board, as D4 , DT , R2A , R2B , RF7 , RF8 , RFA , RFY and even 275800 with processors SH7055, SH7058 and SH7059 integrated.

We have also welcomed the ECUs from Transtron to our repertoire of AI solutions , equipped with processors 4JJ1 , 4JK1 , SH7058 , SH7059 , SH72533 and SH72544 , so you can find a variety of vehicle types from brands like Hitachi , Isuzu , Holden , Case , Caterpillar. and Sumito .

In addition to that, we have also added a solution package for a variety of cars JEEP and Mercedes with engine control units Delphi CRD2 and we even expanded our support for trucks and machinery industrial SCANIA with Motorola EMS S6.

THURSDAY, OCTOBER 12, 2023

Infinite AI Solutions

Loading the 1500 map packs.

Map packs and AI solutions for the long-awaited Delco E98 have arrived, along with over 250 AI solutions for Bosch and Delphi ECUs, and another great bundle of map packages for Bosch and Kefico gasoline cars. Let's dive in!

Infinite possibilities of AI solutions

Throughout this month, we have once again added more than 250 new possibilities to our repertoire of AI solutions .

Our department Diesel worked intensively last month to offer new artificial intelligence solutions such as deactivating the diesel particulate filter ( DPF ), deactivation of exhaust gas recirculation ( EGR ), sensor deactivation Lambda, the deactivation torque monitoring , the calibration of preparation , the deactivation of selective catalytic reduction ( SCR ), start/stop system deactivation and deactivation of the variable turbulence actuator ( VSA ), for many Bosch ECUs, such as EDC17CP11 , EDC17CP42 , EDC17CP55 , MEDC17.9 , EDC17CP22 , EDC17CP48 , EDC17CP68 , EDC17CP27 , EDC17C45 , EDC17CP15 , EDC17CP18 , C81 , EDC17C55 , EDC17C63 , but also engine control units Delphi as DCM7.1A and DCM7.1B and even the much-anticipated Delco E98 which you can find in a wide variety of vehicles, from Alfa Romeo , Changan , Chevrolet , Chrysler , Citroen , DongFeng , Ford , Photon. , GMC , GWM , Sling , Hyundai , Isuzu , JAC , Jaguar , JEEP , JMC , KIA , Kubota , Lancia , Land Rover , LDV , Mahindra , Massey Ferguson , Mitsubishi , Nissan , Opel , Peugeot , Renault , SAIC , Valtra until Volvo .

Delco and Kefico map packs are now a reality

Last month, StageX reached a major milestone covering more than 1500 ECU , so this time we have prepared a special package of map packages to integrate diesel engine support: the most advanced map packages reliable and precise for the long awaited DELCO ECU E98 are now available on StageX!

However, from our department from Petrol Head , new map packs have been added for vehicles KIA and Hyundai , equipped with Bosch ME7.9.8 and ME17.9.11 , and Kefico CPEGD2.20.1 , CPEGD2.20.2 , CPEGD2.20.3 , CPEGD2.20.4 and even CPGDSH2. .26.3 , but also cars Alfa Romeo and Jaguar , equipped with Bosch MED17.3.3 , MED17.8.3 , MED17.8.31 and MED17.8.32 . With such a wide range of options, you can count on comprehensive solutions to satisfy all your requirements. Whether you are working on a modification from Stage 1 or even in one Stage 3+ , StageX It is the best tool to make the most of various modification scenarios.

FRIDAY, SEPTEMBER 8, 2023

StageX Supercar Showdown

More than 1,500 ECUs supported

Map packs for the Ferrari and Maserati beasts, over 250 new AI solutions for Asian brands, and more, and another milestone… We have a lot to talk about, let's get into it!

The FCA queens finally supported

Ferrari 488GTB, Maserati Quattroporte, Alfa Romeo Giulia GTAm…. FCA Crown Jules arrived at StageX!

From now on, everything you need for your beloved Ferrari engine family derivatives (2.9L, 3.0L, 3.8L and 3.9L) is at your fingertips!
You can easily modify those magnificent machines of the FCA group equipped with ECU MED17.3.5 , thanks to our map packages highly descriptive !

It doesn't matter if it's a Giulia either a Stelvio QV , or maybe a GTAm ? Quattroporte in its prime? A 488GTB for new experiences? Unlock the potential of GDI engines most capable in the market with our unparalleled map packs !

More than 250 NEW AI solutions

This month, the possibilities from the StageX AI solution were expanded by offering more than 250 new solutions , this time with a focus on Asian brands !

Our department diesel prepared artificial intelligence solutions such as deactivation of the diesel particulate filter ( DPF ), deactivation of exhaust gas recirculation ( EGR ), sensor deactivation Lambda, deactivation torque monitoring , calibration of preparation , deactivation of selective catalytic reduction ( SCR ), deactivation of the start/stop system, variable. Deactivation of the swirl actuator ( VSA ), for many Bosch ECUs, such as MD1CS003 , MD1CS012 , EDC17C08 , EDC17C10 , EDC17C47 , EDC17C53 , EDC17C57 , EDC17C58 , EDC17C60 , EDC17C72 , EDC17C73 , EDC17CP06 , EDC1 7CP07 , EDC17CP14 , EDC17CP16 , EDC17CP50 , EDC17CP62 that you can find in a wide variety of vehicles produced by Asian brands -and others- such as Hyundai , Kia , Toyota , Sling , Suzuki , Great Wall , LDV , SAIC , SAME , DEUTZ , Force and Foday , but also Lamborghini Tractors, IVECO , Mahindra. , CLAAS , Piaggio and even Citroen , Peugeot , Opel either Ford .

StageX now supports more than 1,500 ECUs

With this update, we have reached another milestone , dear ones StageX users ...From now on, StageX admits more than 1500 ECU from all over the world, which brings us closer than ever to achieve our mission to support all ECUs never manufactured.

Our gasoline bosses, In addition to giving you map packages for FCA Crown Jules equipped with ECU MED17.3.5 , also prepared map packs for you more reliable and accurate for a HUGE line of Hyundai and Kia , ranging from vehicles equipped with Siemens/Continentals SIM2K-140. , SIM2K-141 , SIM2K-142 , SIM2K-143 , until SIM2K-240 , SIM2K-245 and SIM2K-341, to Bosch MED17.9.8

The next time someone asks you about tuning Hyundai/Kia , you can say yes in an instant! As always, all the map packs mentioned offer you a solution. precise and complete for various modification scenarios, from Stage 1 until Stage 3.

THURSDAY, AUGUST 10, 2023

Summer of Chip Tuning and Improvements Vol. IV – Afterparty

Next massive batch of fixes and map packs

Summer is in full swing, but we're not slowing down! Another massive batch of AI solutions for cars and farm machinery has arrived, as well as a new map pack update.

AI solutions for agricultural machinery

To meet this season's high demand, we're providing you with new AI solutions to make it easier for you to meet your customers' needs.

Agricultural machines from brands such as Aebi Shmidt, Caterpillar, Durso, John Deere, Landini, Mc Cormick, Manitu, Steyr and Valtra equipped with Bosch EDC17C49 ECUs are now supported by StageX AI Solutions, such as Diesel Particulate Filter (DPF) Deactivation, Exhaust Gas Recirculation (EGR) Deactivation, AdBlue System Deactivation or Lambda Probe Deactivation.

More than 250 new AI solutions available

In addition to the agricultural sector, StageX has significantly expanded the possibilities of AI solutions for diesel and gasoline automobiles.

In Diesel department, we have prepared AI solutions such as Diesel Particulate Filter (DPF) Deactivation, Exhaust Gas Recirculation (EGR) Deactivation, Lambda Sensor Deactivation, Torque Control Deactivation, Readiness Calibration, Selective Catalytic Reduction (SCR) Deactivation, Start/Stop System Deactivation, Variable Swirl Actuator (VSA) Deactivation, Oil Pressure Correction, Exhaust Flaps Deactivation for a lot of ECUs, such as Bosch EDC17C18, EDC17C19, EDC17C49, EDC17C59, EDC17C69, EDC17C70, EDC17CP05, EDC17CP21, EDC17CP47, EDC 17CP52... EDC17CP54, EDC17CP65... but also some newer models like MD1CP004 , MD1CP006 , MD1CP014 , MD1CS005 , MD1CS006 , MD1CS016 that you can find in cars and vans from brands ranging from Alfa Romeo, Audi, Bentley, Chevrolet, Citroen, Dacia, Dodge, Fiat, Ford, Iveco , Jeep, Lancia, Mercedes, Mitsubishi, Nissan, Opel, Peugeot, Renault, SAAB, Suzuki, Volkswagen and even Porsche.

Furthermore, the Gasoline Management Department has developed AI solutions such as Cold Start Deactivation, Catalytic Converter Deactivation, Evaporative Emission Control System (EVAP) Deactivation, and even Pops & Bangs for Abarth, Fiat, Lancia, and Alfa Romeo vehicles equipped with the Marelli 8GMF ECU.

FRIDAY, JULY 14, 2023

Summer of Melodies – Grand Finale!

New discount system, over 450 AI solutions, and over 30 new map packs

The grand finale of StageX Summer of Tunes has arrived! Huge discounts for PLUS users, over 450 all-new AI solutions (some of them completely FREE), and, once again, a huge number of map packs! Let's get into it!

NEW DISCOUNT SYSTEM

Starting now, all StageXers with a StageX Plus subscription can get up to 40% off ALL AI solutions with an ongoing subscription!

Starting today , every 30 days of continuous, uninterrupted subscription you'll get an additional 5% discount on all AI solutions, on top of the standard 20% discount! It's as simple as it sounds! Just stay tuned , improve your odds , and get additional bonuses every month.

*To qualify for additional discounts, your license must be consecutive.

New AI solutions for AGRI

As the season has already begun , we wanted to keep up with demand and offer the easiest way to meet our customers ' needs with a first batch of agricultural solutions .

Agricultural machines from brands like John Deere , CLAAS , Linder , CASE and New Holland equipped with Phoenix L21, L22, L23, L24, L25 and Bosch EDC17C49 ECUs are now not only compatible with standard StageX AI solutions such as Diesel Particulate Filter ( DPF ), Exhaust Gas Recirculation ( EGR ) deactivation, AdBlue system deactivation, Torque Control deactivation, Readiness Calibration or Lambda Sensor deactivation, but also with completely new AI Stage 1 modifications !

With just one click , you can now increase the power and torque of a wide range of Phoenix ECU- equipped agricultural machines , making them run much more efficiently.

More than 450 NEW AI solutions

In addition to the agricultural sector, we have also extended greatly the availability of AI solutions for cars and trucks.

Our department of diesel prepared artificial intelligence solutions such as deactivating the diesel particulate filter ( DPF ), deactivation of exhaust gas recirculation ( EGR ), the deactivation of the exhaust fins , system deactivation AdBlue, deactivation of the system start/stop , deactivation of the variable turbulence actuator ( VSA ), the deactivation torque monitoring and the accelerator. Deactivation of the valve actuator ( TVA ), deactivation of the mass air flow sensor ( MAF ), preparation calibration and limitation AdBlue dosing for a large number of ECU , like Bosch EDC17C42 , EDC17C11 , EDC17CP19 , EDC17CP58 , EDC16C31 , EDC16C35 , EDC16CP35 , EDC17C84 , EDC17C49. , EDC17C69 , EDC17C79 and TRW EMS2.3 , which you can find in cars and trucks of brands ranging from BMW , Mini , Mercedes , Fiat , Dacia , Nissan , Opel , Renault , Mitsubishi , until Iveco , Mack Truck , Volvo Truck , Renault Truck , Dodge , Lancia , Jeep and even Maserati .

Our gasoline heads , On the other hand, they prepared for you AI solutions as system deactivation Start/Stop , investment of the system Start/Stop , preparation calibration , deactivation cold start , deactivation of the catalyst , deactivation of the variable turbulence actuator ( VSA ), gasoline particulate filter ( GPF ). /OPF ) Deactivation and deactivation of the evaporative emission control system ( EVAP ), for a large quantity of vehicles equipped with ECU Siemens/Continental SIMOS11.1x , SIMOS12 , SIMOS16 , SIMOS18 , SIMOS18.4 , SIMOS18.5 , SIMOS18.10 and Marelli 9GF. .

FREE solutions for DCU modules

That's right! Solutions for modules DCU17PC43 are completely FREE for all users from StageX Plus ! For some vehicles, SCR Solutions must be carried out by modifying both the ECU like the module so that they function properly, such as in trucks Iveco equipped with EDC17C49 and DCU17PC43, for which we also provide medium with This update .

You just need to create a project for both control units , apply Solutions and that's it, your files are ready to be written to both control units.

It couldn't be easier than this!

Dozens of new map packs

Our journey for cover each ECU with map packs descriptive and reliable continues.

Our Gasoline Department, In addition to creating a large quantity of solutions for this update, also prepared for you map packs for the 9GF by Marelli installed in several cars Alfa Romeo, Fiat and Dacia, Bosch MG1CS032, MG1CS042, MED17.4 , MED17.4.2 , MEV17. 4 and MEV17.4.2 are found in vehicles Citroen , Peugeot and Opel and Siemens/Continental ECU MSS54 and MSS70 mounted on a variety of automobiles BMW .

Thanks to the Diesel department, you can count on mappacks of the highest quality for a variety of ECUs Cummins , as CM871 , CM876 and CM2880 , which you can find in a lot of International , Wah Chau , Daewoo , Peterbilt , Kenworth , Photon. , Schacman , SEM , Hangcha , Liugong , ASV Compact , Freightliner & Volvo vehicles and machinery.

As always, all the map packs mentioned above offer a solution precise and complete for various modification scenarios, from Stage 1 until Stage 3.

THURSDAY, JUNE 22, 2023

StageX Summer Tuning Vol. II

Get ready for this season

The John Deere update has arrived, supporting a wide range of Phoenix ECU-equipped farm machines. Let's take a look at it right away!

Map packages for John Deere and Claas are here.

Just two weeks ago we gave you a massive update, with over 200 new AI solutions, unmissable promotions, and awesome map packs, but here we are again with a special update, perfect for Harvest Season!

From now on, you can work on the wide range of John Deere and Claas agricultural machines with Phoenix ECU such as L14, L15, L16, L18, L21, L22, L23, L24, L25, L32, L33, L34 and even L40!
For all of the ECUs mentioned above, you can count on a descriptive and accurate mapping package tailored to your machine! Our advanced systems always find the correct maps and their respective axis, opening up the most reliable ways to tune your vehicle.

New DTC removal algorithms

Not only new map packages, but also relevant DTC removal! The aforementioned John Deere and Claas agricultural machines equipped with Phoenix ECUs have also been covered by our advanced DTC removal algorithms, giving you the easiest way to complete your tune and deactivate the desired codes with just a few clicks.

StageX Summer of Tunes will continue...

But of course, we're not done yet... there's much, much more in the coming weeks at StageX Summer of Tunes!

THURSDAY, JUNE 8, 2023

New to the StageX world: From now on, you can count on AI solutions available for almost all VAG Diesel vehicles, a new Cummins mapping package, and much more. Don't believe it? Let's dig deeper!

+140 new AI solutions

Our latest update gives you access to 140 new AI solutions, fast and applied with a single click. Starting from the older DCM6.2 control units, fitted in Audi, Seat, Skoda, Volkswagen, Citroen, Peugeot, Opel, DS and Toyota vehicles, through the MD1CP004, MD1CP014 and even the MD1CS004 found in numerous VAG group cars such as Audi, Seat, Skoda, Volkswagen and Bentley, in this case you can find solutions such as disabling the diesel particulate filter (DPF), disabling exhaust gas recirculation (EGR), disabling Selective Catalytic Reduction (SCR), disabling the throttle (TVA), disabling the Start/Stop system, readiness calibration, disabling the lambda sensor, disabling the Variable Swirl Actuator (VSA) and exhaust flaps.

Even Marelli's MM8GML and MM8GK gasoline ECUs, found in many Jeep, Abarth, Fiat, and Alfa Romeo cars, are now covered with our one-click AI solutions! Pops & Bangs, catalytic converter deactivation, Evaporative Emission Control System (EVAP) deactivation, or cold start deactivation are now available.

Check out the full list of new AI solutions below or see all supported ECUs directly on the StageX website.

The Mappacks database keeps growing!

Last month, we began releasing map packs for Cummins ECUs, and now the latest batch is available. This time, our Diesel department has prepared map packs for trucks equipped with Cummins CM2220C, CM2200A, CM2350A, and CM2350B ECUs, which can be found in FORD, GAZ, VOLKSWAGEN, FOTON, DONGFENG, BRILLIANCE, RAM, HYUNDAI, SKYJACK, TEMSA, WIRTGEN, ROSTSELMASH, NEW HOLLAND, and KENWORTH trucks. These map packs allow you to create a complete solution for a variety of editing scenarios, ranging from Stage 1 to Stage 3.

On the gasoline front, here is the map package for Siemens/Continental MSD80 and MSD81 installed on BMW and ALPINA cars, also you can freely modify PORSCHE cars equipped with SDI3 and SDI4 ECU, sure our map package will cover all your modification needs.

Summer is coming…

We're always pushing the boundaries, striving to revolutionize the industry. That's why a few weeks ago we released one of the most significant updates ever for the StageX app and related services. This is not only to continue our ever-growing support for a wide variety of ECUs, but also to continue our revolution, unlocking possibilities for even more exciting features, solutions, and workflow enhancements for all of you.

That said, we're aware that some users have been experiencing issues with the new version of StageX over the past few weeks, and we want to reassure you that we're working hard to resolve any issues. Additionally, we're preparing something amazing for all active StageX Plus users, which will be unveiled soon.

Once again, we want to thank you all for continuing to drive the StageX Revolution forward, because we wouldn't be us without you.

Wednesday, April 19, 2023

Primavera StageX: More than 500 new solutions are ready for you

Primavera StageX: More than 500 new solutions are ready for you

A basket full of free updates and fixes

Experience the power of the latest StageX update! Get access to more 500+ new AI solutions , 60+ map packs for multiple ECUs, FREE fixes , and a huge discount on DTC removal ! Yes, it's a reality!

10 free solutions

Let's start from the beginning: Take advantage of our latest promotion and get 10 FREE AI solutions ! This offer is available exclusively to StageX Plus users from April 19th to May 19th . Don't miss this limited-time offer and boost your ECU tuning capabilities with StageX's advanced AI solutions . Check out the list of ECUs eligible for the promotion at the bottom of the email and upgrade to StageX Plus today.

*Only newly added AI solutions are eligible for this promotion. See the full list of new AI solutions below.

DTC Removal with a 66% Discount

Attention all StageX Basic users ! Starting now, you can get StageX Advanced DTC Removal algorithms at an unbeatable discounted price. Get 66% off today and choose our Advanced DTC Removal algorithms for just 15 Red Coins . Plus, if you're also a Flex Full Master user, you can get them for just 10 Red Coins !

More than 500 new AI solutions

This time we've outdone ourselves and delivered a massive update to the StageX AI Solutions database. From DPF, EGR, and SCR deactivation, through Start/Stop, Speed Limiters, EVAP, TVA, VSA Lambda to Cold Start deactivation , even Pops & Bangs, and much more!

From the older Bosch EDC16 , through the EDC17Uxx, EDC17Cxx, EDC17CPxx , to Marelli MJ6 and MJ8 and Delphi DCM3.7 , you can count on that on all VAG Diesel vehicles like Audi, Seat, Skoda and Volkswagen (and many more!), equipped with those ECUs, our AI solutions will revolutionize your daily tasks with just one click!

Marelli Petrol MM8GMW and MM8GW ECUs , installed in various Abarth, Fiat and Dodge cars, are also covered with our one-click AI solutions now!

Cummins Mappacks have arrived

As promised in our last update, our Diesel Department has prepared something special for you this time. In addition to this massive amount of new AI solutions, our team also delivered comprehensive and accurate mapping packages for Cummins and Delco ECUs.

From now on, it can work with a variety of cars, trucks, agricultural machines, industrial machinery, buses and many other types of vehicles equipped with Cummins CM2150E, CM2150D, CM2150C, CM2220A and CM2250 from brands such as Nissan, John Deere, Freightliner, Ford, DAF, Dong Feng, Agrale, Sterling Trucks, Kenworth, Skyjack, Foton, Volkswagen, Mercedes, JAC, Hitachi , crawler excavators and many, MANY more...
Delco E87 installed in Opel cars also became easy to remap, thanks to our descriptive and highly accurate mapping packages.

Our petrol heads, on the other hand, have prepared complete mapping packages for the Marelli MM8GMW and MM8GSW installed in Abarth, Fiat, and Dodge cars, the Siemens/Continental SDI6 installed in Porsche, and the Bosch MG1CS003 installed in a variety of BMWs.

All of those newly added map packs , like all the previous ones, are completely suitable for any modding scenario, from Stage 1 to Stage 3 .

StageX DTC Clearance Directly in WinOLS5!

DTC Removal is now also available in EVC WinOLS5! After any purchase in Solution Manager (F7), you'll gain access to DTC removal algorithms, within the current project, completely FREE at no additional charge! No matter if you purchased an open or closed map package or any available AI solution , you'll get DTC removal for your project as a FREE bonus!

Note: All StageX services are now available in EVC WinOLS Solutions Manager (F7) under the PowerDivision brand. Be sure to keep your WinOLS5 updated to the latest version at all times.

THURSDAY, MARCH 9, 2023

StageX becomes free software

A shower of advantages

One of our key goals from the beginning has been to create an inclusive tuning environment, allowing anyone to participate in our journey within the mechatronics industry and recalibrate vehicles on their own, regardless of their experience level. We're committed to maintaining this commitment and advancing our modification revolution alongside all of you.

Our advanced MapEditor will handle any task, from EGR OFF, GPF OFF, SCR deactivation, speed limiter disabling, and even Stage 3+ modifications, all right from your browser (also on MacOS!)

Clear any DTC whenever you want with just a few clicks, thanks to our advanced DTC removal algorithms or, additionally, purchase your Mappack for any of the more than 1250 control units currently supported by StageX.

Create your own knowledge database with the "My Solutions" feature and start saving time on repetitive tasks, or take advantage of the AI Solutions feature and modify control units with just one click!

All that, and much, much more, from a Basic License, RIGHT NOW!

*Mappacks, DTC Removals, AI Solutions, and Checksum services are paid per project.

No time limits!

Unlike StageX DEMO, there is no time limit on your license, and what's more, anyone who already had a DEMO or other license that simply expired will also be able to rejoin Industry Revolution, if it hasn't been too long, you'll even see your old projects again.

FREE Map Packs & DTC Removals!

To help you get started on your journey to StageX Remapping Revolution, we're giving you access to full Mappacks and DTC removal for MD1CS004, MED17.5, EDC17C46, DCM3.4, SID807 ECUs, and even the DQ200 TCUs completely FREE. You'll then get pre-built projects with each of those ECUs to play with and experience the full potential of StageX for yourself.

33% off for Flex Masters!

If you are an active Full Flex Master (FLS0.5M) user, you will get a special 33% discount on map packs and DTC removals on your basic license (compared to the current basic license price).

Get your F7!

Take advantage of StageX services directly in EVC WinOLS! If you're not yet a fan of F7, here's a step-by-step guide on how to register your EVC ID and enjoy StageX services directly within EVC WinOLS.

All map packages for over 1,250 control units, covering thousands of vehicles and geared for even the toughest stages, plus our fast and easy AI solutions, are available at the touch of a button in WinOLS. So what are you waiting for? If you're already a WinOLS user, be smart: Get your F7 and start having fun with StageX Services right away.

TUESDAY, MARCH 7, 2023

StageX 10/10

More than 10 reasons to be a StageXer

Mark your calendars, tuners! On March 10th, we'll be celebrating all of you amazing StageXers.
For International Day of Genius, we have something... well... SOMETHING AWESOME!

10 out of 10!

10 solutions for only 10 red coins each, available for both: directly in StageX and WinOLS Solution Manager!
And we mean, Stage 1, GPF OFF, DPF OFF, SCR OFF, Start Stop ... you name it! All solutions, regardless of type, will have a discount of just 10 red coins (or 10 credits with F7 in WinOLS) for all WinOLS users. StageX Plus . Be smart, don't miss this opportunity! Better hurry, because this offer will last only 24 hours March 10 (UTC+2).

10 out of 10!

And we're not done yet! Starting today (March 10, 2023) and continuing through the end of the month (March 31, 2023), all unopened map packs available in WinOLS Solution Manager will be discounted by 10 credits each for all StageX Plus users.
If you are not yet a fan of F7, there is one complete step-by-step guide on how to register your EVC ID and get the full set of benefits offered by StageX services directly from EVC WinOLS .

High-quality map packs!

But of course, we haven't forgotten about map packages! This time we have a special delivery of ECU support for gasoline engines. Our highly descriptive and accurate map packages are now available for MG1CS024 equipped BMW and Toyota vehicles. MG1CS201 installed in many brands, such as BMW, Brilliance, MINI, Morgan, Rolls Royce or even Toyota . You can also modify any Mercedes equipped with SIM266 ECU , which gives you (as with all our map packages) the ability to make modifications up to Stage 3, thanks to the accurate and understandable map packages. Plus, each of the new MG1 map packages contains over 520 precisely described maps.
And since there are no new Diesel map packs this time, don't think we're just twiddling our thumbs ;) Our Diesel Department is working hard to bring you a truly exciting update. SPECTACULAR for next month, so stay tuned for more news. You won't be disappointed, that's guaranteed!

Make sure you stay tuned and follow us closely, because we still have an ace up our sleeve that will be revealed in the next round ;)

THURSDAY, FEBRUARY 9, 2023

StageX beyond the limit

New map packs, new fixes, increased limits!

Another big update just arrived! get to StageX! Over 40 new map packs for a wide variety of ECUs, new exclusive AI solutions, and improved limits in My Solutions!

Starting with map packs, our petrol masters have just released highly descriptive and accurate map packs for BOSCH MEVD17.2.7 and MEV17.2.2 equipped in BMW and MINI, Accurate map descriptions for SDI8 ECUs mounted in numerous cars Porsche and SIEMENS/CONTINENTAL SIM271DE and SIM271KE for Mercedes-Benz vehicles.

Moving on to the diesel department, our guys have just released a variety of different ECUs for various types of vehicles, from Visteon DCU-101, DCU-102, DCU-104 and DCU-106, mounted on Citroen, Peugeot, Ford and Land Rover Cars, through DENSO ECU like 275800 or F4HD that you can find in Hyundai Trucks, SH72546 mounted on cars Hyundai and Kia, RX703200, 89564, YK71RV850, RV850 for trucks HINO, DENSO 275870, 275770 for Sinotruck and Landini trucks or John Deere's Agricultural machines, even up to some industrial machines from brands like NEW HOLLAND, XCMG, JCB and Takeuchi equipped with ECUs such as RX703200, 275870 and 275770.

Ladies and gentlemen: AI solutions for Marelli MJ9DF and FoMoCo DCU17PC43 they just came out!

From now on, you can perform modifications such as deactivating Selective Catalytic Reduction (SCR), deactivating Exhaust Gas Recirculation (EGR), deactivating the Start/Stop system, deactivating the speed limiter, deactivating the Diesel Particulate Filter (DPF), and deactivating the throttle valve actuators (TVA) on Fiat, Alfa Romeo, and Lancia cars equipped with a Marelli MJ9DF ECU in just a few clicks!

Furthermore, for added convenience, after performing SCR OFF or DPF OFF modifications, no reset is required and you can freely disconnect pumps or sensors.

In addition, you can perform the Selective Catalytic Reduction (SCR) deactivation modification on the submodule DCU17PC43 mounted on a variety of Ford automobiles equipped with the almighty ECU SID212.

Although this is already a big update, we're not done yet.

After long hours of optimizations and server resiliency testing, we've achieved what was previously impossible... Starting today, My Solutions limits increase to 5000 for all StageX PLUS users!

We all know that there is nothing more important than knowledge and My Solutions is nothing less than your very own database. It was never our intention to limit your working possibilities in StageX, but to keep our systems stable and running smoothly all the time, we sometimes have to make difficult decisions that can have an impact. That said, our upcoming Advanced License will also have UNLIMITED My Solutions, among many other improvements and goodies coming soon.

Phew... it was awesome, but as always, we want to encourage you to stay tuned for the next monthly updates, because we're preparing something unmissable for all of you!

Join StageX Plus Revolution and update your possibilities.

THURSDAY, JANUARY 19, 2023

January DTC Update

Even more cars and trucks

As every month, another StageX update has just arrived! This time we have a DTC removal solution for a variety of cars and trucks.

Now you can easily remove the DTC in the control units of Delco such as, for example, E87 and E98 in cars Opel and Chevrolet , the same easy removal is also available for EMS S8 and EMD1 in Scania Trucks, Marelli MM10JA mounted on ALFA ROMEO and ME17.8.5 that you can find on a variety of Sea-doo, Can-am and Polaris vehicles.

Thanks to this simple DTC removal solution, you'll clear all the necessary trouble codes in no time! Plus, StageX always focuses on efficiency, so this feature is also as quick and easy as it gets. Simply go to the DTCs tab, enter or select the desired codes, click Clear Codes, and that's it—your job is done.

Wednesday, January 11, 2023

WinOLS integration becomes a reality

Plus, another batch of qualitative maps for gasoline and diesel.

We are proud to announce that the integration of StageX and EVC WinOLS, two powerful ECU recalibration tools, is NOW AVAILABLE!

This integration of StageX and EVC WinOLS allows users to access powerful StageX features such as Quality Mappacks and AI Solutions, directly from the new EVC WinOLS Solution Manager. As always, in the simplest way possible.

Summer of promotions

Great discounts and FREE solutions

The StageX Summer of Promotions begins now! Over 200 new AI solutions, unmissable discounts, free DPF and EGR solutions, and another batch of map packs. Let's dive in!

FREE AI Solutions

We're off to a great start! Starting now, all StageX Plus users can get Diesel Particulate Filter (DPF) deactivation and Exhaust Gas Recirculation (EGR) deactivation AI solutions for a variety of Volkswagen , Seat , Skoda , Audi , and BMW vehicles completely free of charge. The ECUs included in this promotion are listed below:

EDC17C06, EDC17C41, EDC17C46, EDC17C50, EDC17C54, EDC17C56, EDC17C64, EDC17C74, EDC17C76, EDC17CP02, EDC17CP04, EDC17CP09, EDC17CP14, EDC17CP20, EDC17CP24, EDC17CP44, EDC17CP45, 49, EDC17CP54, EDC17CP74, EDC17U01, EDC17U05

*The aforementioned promotion lasts until further notice.

-30% discount on AI solutions

Not only do we offer you a large number of free AI solutions , but we're also offering you an incredible discount on all of them! Until 07.06.2023 , all active StageX Plus users can purchase solutions or bundles of them with a 30% discount instead of the usual 20%. There's never been a better time than now to take advantage of the highest quality AI solutions on the market!

More than 200 NEW solutions

This month, we bring you a large batch of AI solutions covering most of BMW and Mercedes diesel vehicles with ECUs ranging from EDC17C06, EDC17C41, EDC17C42, EDC17C43, EDC17C50, EDC17C56, EDC17C76 to EDC17CP01, EDC17CP02, EDC17CP09, EDC17CP10, EDC17CP45, EDC17CP46, EDC17CP49, EDC17CP57 , to MD1CP001, MD1CP002, MD1CP032 and MD1CS001.

With just a few clicks , you can reliably deactivate the Diesel Particulate Filter ( DPF ), Exhaust Gas Recirculation ( EGR ) and Selective Catalytic Reduction ( SCR ), but also apply readiness calibration , deactivate the Lambda sensor , torque monitoring and the Start/Stop System, and also deactivate the Throttle Valve Actuators ( TVA ) or Variable Swirl Actuators ( VSA ) – all with the highest possible reliability.

Additionally, gasoline ECUs , such as MM8GSF and MED17.3.1 that can be found in a variety of Alfa Romeo , Fiat and Lancia vehicles, were covered by Pops & Bangs , Evaporative Emission Control System ( EVAP ) Deactivation, Catalytic Converter Deactivation , and Cold Start. AI Deactivation Solutions Also Available!

Mappack updates never stop!

As we continue our journey to cover every ECU in the world with high quality descriptive map package , our Chief Petrol department has prepared for you map packages for the Marelli MM8GSF fitted to various Alfa Romeo and Fiat cars, Bosch MED17.3.1 found in Lancia and Alfa Romeo vehicles, Siemens/Continental MSD85 and MSD87 ECUs fitted to a variety of BMW and Rolls Royce cars.

Our Diesel department, on the other hand, gave you the opportunity to work on the Cummins CM2850A ECU, which you can find on a variety of Camos , Pauny and Jacto Agricultural Machines .

Our map packages offer an accurate and comprehensive solution for various modification scenarios, from Stage 1 to Stage 3.

TUESDAY, MAY 23, 2023

StageX looks ahead to summer

New AI solutions and map packs coming soon

Plus, another batch of qualitative maps for gasoline and diesel.

We are proud to announce that the integration of StageX and EVC WinOLS, two powerful ECU recalibration tools, is NOW AVAILABLE!

The new WinOLS Solution Manager can be opened by pressing the F7 key or clicking the puzzle icon in the top menu. From there, you'll see a list of map packages and AI solutions available for selected ECUs that you can purchase with your EVC credits.

No, that's not all! Newly crafted map pack menu

As usual, we've prepared another set of Mappacks for diesel and gasoline vehicles. This time, our gasoline experts have created quality mappacks for the B MW and MINI Bosch MED17.2, MEV17.2, MEV17.2.1, and MEVD17.2.2 ECUs , and our diesel department has just released accurate mappacks for the Visteon DCU-102 and DCU-106, and a specialized, more industrial-grade, Bosch EDC17C87, mounted on, for example, BOBCAT compact skid-steer loaders.

Remember, all of these map packages are available in WinOLS Solutions Manager right at launch, as are all of our new releases.

THURSDAY, DECEMBER 22, 2022

StageX x WinOLS – Closed Beta

StageX will be more open than ever!

Merry Christmas tuners!

This is our last giveaway for this year, but it's awesome: we're giving you the chance to use upcoming StageX features right before they're released!

From the beginning, our mission was to create an inclusive environment for tuners, where everyone, regardless of their level of expertise, can embrace our journey in the mechatronics industry and perform recalibrations on their own, in their own way. We want to keep this promise and continue our remapping revolution with you!

We're proud to announce that starting today, you'll be able to join the StageX Closed Beta program to test StageX features directly in EVC WinOLS! You'll have the option to get premium map packages (and more!) directly from the new WinOLS Solution Manager . As always, it's easy! All you need to do is register at stagex.ai/evc-winols and wait for our response*.

*As this is a closed beta program, we will only select a few accounts for our testing environment.

Don’t worry: StageX Editor will continue to expand with new features and possibilities!

Nothing changes in our development plans for StageX Editor, because 2023 promises to be a big turning point for StageX again!

But as we know, many of you are simply accustomed to working on EVC WinOLS and it is more convenient for you to stay on this platform you have been accustomed to for all these years.
That's why we're expanding our internal capabilities beyond just one editor and giving you the opportunity to work in the most convenient way possible!

And again...Thank you for all your support and trust in StageX, it is thanks to you that this Revolution becomes a reality.

TUESDAY, DECEMBER 20, 2022

Endless Christmas gifts!

Exclusive DTC clearing support for EMS2.4 and all Simos19.x ECUs

The year may be ending, but we're not done giving gifts yet!

This time we offer you a complete solution DTC Clearance for all ECUs SIMOS19.x for cars Audi, Volkswagen , Porsche , Seat , Skoda and Cupra .

In addition to that, we will also be releasing exclusive ECU support. EMS2.4 mounted on many trucks of brands such as Mack Trucks , Renault Trucks , UD Trucks and Volvo Trucks. From now on, you can remove any unwanted DTCs with just a few clicks.

See the complete list of newly supported control units via DTC clearing below.

*DTC removal for EMS2.4 only supports Flex reading

Ongoing promotions!

All StageX Plus users get 5 free fixes per day for almost any Siemens/Continental Diesel ECU, and if you're also a Flex Full Master (FLS0.5M) user, you're also eligible to take advantage of the same 5 free fixes per day for SIMOS19.6 at no additional charge.

We still have an ace up our sleeve, so stay tuned for upcoming updates !

WEDNESDAY, DECEMBER 14, 2022

StageX Plus for Simos 19.6

Five free solutions per day

Five free fixes per day on Simos 19.6 ECUs with StageX. Until December 31, 2022 , Flex full and StageX Plus owners (code FLS0.5M + STX0.2) will have the opportunity to use these services without additional cost:

Modification of stage 1
Deactivating the gasoline particulate filter (GPF/OPF)
Catalyst deactivation
Deactivating the speed limiter
Deactivating the Start/Stop system

Simply load your ORI file and automatically access solutions.

TUESDAY, DECEMBER 6, 2022

Welcome to StageX 2.0

The Revolution - Act II

Hello tuners!

It's been a long way since the first release of StageX 1.0. Initially, just a few map packs and solutions were available two years ago... day after day, StageX grows to become the industry standard in many ways. With over a thousand map pack-compatible control units , literally MILLIONS of maps inside, and nearly the same coverage, the best DTC removal system on the market.

Now is the time to step up our solutions game!

From now on, you can use the new AI Solutions system in StageX. Not only is it better, but from launch we offer support for almost all Siemens and Continental diesel ECUs!

Combine that with a completely revamped editor , new map packs , great promotions, StageX Academy where we'll teach you how to perform simple remapping actions at a glance, and FREE SOLUTIONS for StageX Plus users.

Sounds good? Amazing? Grab a sip and let's get into the details!

Completely new AI solutions!

We've completely rethought, redesigned, and reworked the AI solutions in StageX. From now on, all new solutions will be prepared for every scenario, no matter which compatible ECU calibration you load—we've got you covered.

Our AI will automatically find and recalibrate all the necessary sectors, starting from your daily tasks, firstly disabling EGR or DPF, then turning off systems such as Start/Stop, torque monitoring, speed limiters and even completing a Stage 1 modification, all with just a few clicks.

And, as we've already mentioned, we already offer solutions for almost ALL Siemens and Continental diesel ECUs!

Specifically, from PPD1.x , through PCR2.1, SID206, SID310, SID807 , to SID914. Simply open our Supported Vehicle List and search for all ECUs compatible with the new AI solutions.

*All previous automated solutions will continue to be available until replaced with new AI solutions.

StageX 2.0

Fixes aside, we've also tweaked a lot of other things!

We've completely redesigned our engine to run smoother than ever, even on older, crankier laptops. You'll find yourself navigating dense areas of the map, with lots of shifting and lower zoom, all with complete ease.

In both Hexdump viewports (Text and 2D), you'll now see all of your maps' axes, making your workflow even easier and more visually clear. In addition to the buttons to show/hide unnecessary map types, you can now also toggle between overlay and border for potential maps . If you want to keep them all but hate those messy overlays, we've also added additional arrow buttons, allowing you to quickly jump between maps. The idea is to make remapping even faster and provide a more comfortable experience.

All changes made to maps will now be highlighted in the map list in the left sidebar, and the folder will also be colored after changes to any map within it. This is so you can keep track of changes and never have to think back to yourself, " Have I adjusted this map yet? "

Above all, we've made a lot of improvements and fixes here and there, but it's hard to explain them all in this text, so you can see the full list in the Changelog below.

Special hint: The next batch of Mappacks

Along with all those great offers, changes, and improvements, we haven't forgotten about Mappacks!

This month we're bringing you another exciting batch of map packages for transmission control units like the Aisin AQ450, which can be found in Audi, Volkswagen, Skoda, Seat , and the first generation of the Porsche -specific PDK TCU developed by Siemens/Continental.

Here's a great addition to the Gasoline Department ! Continental SIMOS19.2, 19.7 and 19.8 for VAG Group cars , SDI9 ECUs specific to Porsche cars , and Bosch ME17.7 that you can find in Mercedes-Benz vehicles ; all maps in each map package are, as usual, not only accurately described, but you can be sure that every axis and every sector will correspond to reality.

Finally, we bring you the next batch of highly descriptive map packages from our Diesel Department for Denso engine control units fitted to Lexus and Toyota cars, RX703200 and RX-OSEK850.

New FREE DEMO & SOLUTIONS

To thank the entire StageX Plus user community for making it this far and for their support throughout this time, we'll be giving away 5 FREE AI SOLUTIONS PER DAY throughout December! List all ECU promoters on the "New AI Solutions" list.

Not only that... you'll also receive a 20% discount on all other solutions (or AI solutions that exceed the limit) regardless of their type! And this promotion has no expiration date.

But if you're new to the platform , a returning user who just wants to see what's new, or even if you've already tried the DEMO , we also have some unmissable news for you.

Every account will get 6 pre-built projects to play with and test out the full capabilities of StageX . You’ll also be able to load up virtually any ECU you want to see what it’s like to be part of our subscription; even try out some of those new solutions. Additionally, we’ve enabled map packs for demo accounts on ALL MD1CS004, MED17.5, EDC17C46, DCM3.4, DQ200, and SID807 calibrations so you can access and play with them however you like.

The StageX Academy is a reality

If you're new to tuning or just looking for help, you can count on StageX Academy! Our AI assistant, AleX, will teach you how to handle simple daily tuning tasks, such as activating the gear display, disabling EGR, disabling the speed limiter, disabling the torque limit, clearing DTCs in the TCU, or even enabling POPS and BANG.

We're already releasing six episodes with the promise of many more to come... until we've covered every possible scenario.

WEDNESDAY, NOVEMBER 16, 2022

Following BMW DTC Eliminations

Clear DTCs in zero time!

Hey StageXer, just a few weeks until we reveal the biggest StageX update yet! Warm up and get moving!

So before you leave, we have another batch of algorithms for you. DTC Clearance for the BMW MEVD17.2.x ECU. This time we are talking about MEVD17.6, MEVD17.2.8, MEVD17.2.9, MEVD17.2.G and MEVD17.2.H.

From now on, thanks to this update, the whole family from ECU MEVD17.2 is covered and therefore, together with our accurate Mappacks, every StageXer will be able to complete modifications from start to finish in the fastest, yet still accurate, way possible.

Don't forget that on these new ECUs, as with many other supported control units, you can check what's inside our map packages directly at ECUlist.stagex.ai.

FRIDAY, NOVEMBER 4, 2022

November Unleashed Map Packs

Cars, tractors, and crawler loaders... what else?

In this episode of the update of StageX Revolution, we offer you an incredible set of map packs!

ECU and TCU for cars , tractors , chain loaders, diesel and gasoline , you name it! Each one contains literally hundreds of precisely described maps that allow you to make virtually every adjustment needed on a wide range of vehicles. Porsche , Mercedes , Maybach , Kubota , Opel , Saab , Audi , Seat , Skoda and Volkswagen .

This time Let's start from the TCUs The second generation of Bosch DQ381 available in the Group's cars VAG is now completely covered with highly detailed map packages , so you can expand your previous offering beyond the ECU and tailor your tunes to even the most demanding customers, improving gear shift speed, removing additional limiters, smoothing gear transitions, or any other tune you can think of. And this thanks to more than 600 maps individual !

Let's continue with the department Diesel which this time focused on some machinery Agricultural built by the brand Kubota offering them another range of possibilities to work in Denso ECUs as 275770 , STD either STD04 , bringing something unique to the Classics of Opel & Brands Saab equipped with Bosch PSG16.

Last but not least, our bosses of gasoline They prepared other very detailed map packages for Porsche cars that run on SDI10.x and Continental SDI21.x, Mercedes vehicles equipped with Bosch MED17.7.3 and even Maybachs with ME17.7.8 aboard.

Before revealing other surprises and the biggest StageX update yet , you can expect another DTC update to come out in a few weeks, as always!

Keep following us for upcoming news, and we promise... you won't be disappointed!

WEDNESDAY, OCTOBER 19, 2022

New MEVD17.2 ECU DTC Solutions

DTC removal algorithms in StageX continue to improve.

Welcome October and welcome to our next update. DTC Clearance! From now on, you can easily remove DTCs on a valuable variety of BMW and MINI gasoline vehicles equipped with ECUs such as MEVD17.2, MEVD17.2.3, MEVD17.2.4 and MEVD17.2.5.

This complements our highly descriptive and accurate map packages for those control units, and from now on, you can complete your modification from start to finish as quickly and easily as possible!

Don't forget that also on these ECUs, like many other compatible control units, it is possible to check what is inside our map packages directly on ECUlist.stagex.ai

Join StageX Plus Revolution now! It's time to upgrade your workshop's capabilities.

New DTC algorithms

FRIDAY, OCTOBER 7, 2022

SIMO 19.3 and 19.6 now available

Over 30 Amazing New ECUs in StageX!

We're starting off with a bang, with an awesome release of map packs for SIMOS 19.3 and 19.6 that contain up to 650 maps High precision and accuracy. This allows you to enable endless possibilities for virtually any tune. Yes, we're even talking about Stage 3! - in vehicle Audi, Porsche, Seat, Cupra, Skoda and Volkswagen equipped with these ECUs.

And that's not all because there's much more!

We've prepared another amazing batch of TCUs for you, this time from Aisin, such as the AL750, AL1000, and AQ250, so now you can also tune and customize gearboxes on Audi, Volkswagen, and Porsche equipped with those control units to suit any need!

In addition, we always focus on the diesel department, so we have prepared accurate map packages for Isuzu trucks, equipped with ECU 4KH1, 4H06, 4H0, 4H10, 4H15, 6H04, 6H07, 275800 Denso and many Denso-equipped Volvo cars in the Volvo range. VED/VEA ECU.

In addition, for gasoline engines, in addition to the new ECU SIMOS 19.3 and 19.6, We also offer you the possibility of reassigning Bosch MG1CP002 and MG1CP004 installed in Mercedes cars, thanks to our highly descriptive and accurate map packages.

Remember that on these new ECUs, like many other supported control units, you can check what's inside our map packages directly at ECUlist.stagex.ai

And as always, stay tuned for upcoming monthly updates, because we're preparing something for all of you that you can't miss!

MONDAY, SEPTEMBER 26, 2022

StageX TRW Exclusives

New DTC removal algorithms for EMS2.3 and MED9.1

The expansions of StageX in solutions of DTC Clearance continue to accelerate! This time we present you an unmissable exclusive for the TRW EMS2.3 diesel ECU installed in Nissan, Mack, Renault and Volvo trucks!

And that's not all, because we've cooked up a ton of amazing new things. From now on, you can also easily remove the DTC codes in the Bosch gasoline ECU such as, for example, MED9.1 in cars Audi, Seat, Skoda and VW, MED9.1.1 and MED9.1.2 for Audi and Lamborghini, MED9.1.3 for Audi, Seat and VW, MED9.1.4 for VW and last but not least, MED9.1.5 installed in vehicles Audi.

Thanks to our simple solution DTC Clearance, After each modification, you will be able to delete all necessary trouble codes in zero time, and these operations are always facilitated by our comprehensive and accurate mapping packages.

StageX is always focused on saving you time, so this feature is as quick and easy as it sounds. Simply go to the tab DTC codes , enter or select the desired codes, click Delete Codes and that's it, your work is done!

By choosing the StageX Plus subscription, you will get all the Mappacks , DTC solutions, and new checksum calculations for your projects at no additional charge!

Join the StageX Plus Revolution and upgrade your capabilities. Stay tuned for upcoming big updates!

*DTC removal solutions available for unencrypted files only.

FRIDAY, SEPTEMBER 9, 2022

Summer is ending, but the map packs are endless.

Upcoming map packages: DENSO Diesel and Bosch Gasoline ECUs

New month, new map pack update, as always. This time we're releasing a new batch of map packs for DENSO control units for Renault, Nissan, and Subaru cars and trucks , such as the P729, DT, D3 and D4 ECUs.

Moreover we always focus on petrol engines so we have prepared many more interesting map packages for Mercedes Bosch MED17.7.2, MED17.7.3.1 and MED17.7.7, for BMW and MINI we have prepared MEV17.2. MEVD17.2.3, MEVD17.2.4, MEVD17.2.5, MEVD17.2.8 Bosch ECU and speaking of ALFA ROMEO you can now use precise and accurate map packages for Magneti Marelli MM10JA.

Are you ready to improve your business? Check out the full list of StageX compatible ECUs now, including more than 1000 ECU of all manufacturers and brands.

FRIDAY, AUGUST 26, 2022

StageX DTC Monthly Update

Next ME17.1 and ME17.5 DTC Clearance Algorithms

As promised month after month, the list of resolved DTCs is constantly growing. This update allows you to easily remove DTCs on a variety of new ECUs, such as ME17.1.1 for 6.75 Bi-Turbo engines, ME17.1.6 for 6.0 Bi-Turbo, ME17.5 for 1.6 MPI and 2.5 MPI engines, ME17.5.2, ME17. .5.20 & ME17.5.24 for 1.0 MPI engines and ME17.5.22 for 1.6MPI engines, which complements and completes our high-precision mappacks for these control units, so you can complete your modifications from start to finish as quickly as possible.

Consult now the full list of supported ECUs from StageX, which includes over 1000 ECUs from all manufacturers and brands, and Join the StageX revolution now.

Wednesday, August 10, 2022

Over 90% coverage of ALL diesel ECUs

New StageX map package update covers over 60 new ECUs

As promised, this update comes with Bang!

With this version, you have access to comprehensive and accurate map packages for over 36 control units DENSE such as, for example. Mazda SHY, SHT, SHS, SHM, SHJ, SHH, SHF, SHD, SHB, SHA, SH7, SH6, SH5, SH4, SH3, SH2, SH1, SH0, RF8, RF7, R2BP, R2BH, R2BG, R2BF, R2AX, R2AW, R2AJ, R2AG, R2AC, R2AB, R2AA, 4D56 and Mitsubishi STD, 4P27, 4D56, RA6, 6M60.

From now on, you can work on virtually any diesel control unit and rest assured that StageX has you covered with a map package – our map package database surpasses itself and now covers over 90% of ALL diesel control units!

But of course, this huge coverage of new switchboards DENSE That's not all because we have added another important batch of more than 20 new Bosch Gasoline ECUs such as VAG MED9.1, MED9.1.1, MED9.1.2, MED9.1.3, MED9. 1.4, MED9.1.5, MED9.5, MED9.5.10. Mercedes MED17.7.1, MED17.7.5 ECUs and BMWs MEVD17.2.G, MEVD17.2.H, MEVD17.2.6, MEVD17.2.9 for all their engine variants.

Check out our complete list of compatible ECUs now! StageX , which already includes more than 1000 ECUs from all manufacturers and brands!

MONDAY, JULY 18, 2022

New DTC solutions for MED17 and ME17 ECUs

The next batch of DTC fixes has arrived.

In this monthly DTC update, we provide you with new algorithms for easy DTC removal in ME17.5.26 for 1.0 and 1.6MPI engines, ME17.5.6 for 2.5 MPI engine, MED17.1.10 for 2.0 TFSI engine, MED17.1.11 for 3.8 FSI and 4.0 TFSI engines, MED17.1.21 for 1.4TFSI engine and MED17.1.27 for 1.0 and 1.4TFSI engines.

Stay tuned and don't miss the upcoming updates because they're going to be GREAT! We'll be delivering not only new map packages for a huge variety of ECUs, but also some amazing new features.

New DTC Algorithms

Check out the now Complete list of StageX compatible ECUs , with over 1000 ECUs from all manufacturers and brands.

MONDAY, JULY 4, 2022

More for this summer, we give a big welcome to the ECUs of

DENSE

This summer is coming explosively!

The moment everyone was waiting for... The first batch of DENSO control units (!) has arrived, plus many Transtron ECUs covering a large number of Heavy Duty vehicles and another increase of MED17.1 and MED17.5 petrol ECU families!

You ask, we deliver

Starting with this update, we are starting to roll out high-precision map packages for DENSO control units starting with SH7055, SH7058, SH7059.

In addition, we have expanded support to heavy machinery equipped with Transtron ECUs such as SH7059, SH72533, SH72544 and 4Jxx.

TUESDAY, JUNE 21, 2022

Dark mode is now a reality!

StageX continues to grow strong

With the easy DTC removal dedicated to a variety of upcoming gasoline ECUs from the MED17.5 family, to complete our accurate mapping packages for those control units, we also introduce a new batch of enhancements to the application StageX , like the dark mode , new toggles, and app-wide optimization to make it the fastest, most reliable software you've been looking for.

Don't miss this opportunity: be part of the StageX Plus revolution now!

Welcome Dark Mode

From now on, you can customize the look of your StageX app to your liking.
The dark theme revamps every color, icon, and font in the app for a completely darker look. Whether you're a night owl who wants to give your eyes a rest or just prefer a darker look, you'll find something you'll love.

To switch to dark, simply open the Configuration ⚙️ in any project and in the drop-down menu Theme, choose Dark.

But that's not all! In the bottom status bar, you'll now see three additional toggles to easily hide/show the desired map type, for a much cleaner look when needed.
In addition, we've optimized localization and performance across the entire application for even faster and more reliable workflows.

Look out for more changes and features in upcoming updates!

MONDAY, JUNE 6, 2022

After 33 ECU with Mappacks!

New ECUs from Temic, Continental, Motorola and Bosch now on StageX!

With this update, we are introducing the next batch of map packages for over 30 new ECUs manufactured by Temic, Motorola, Bosch or Continental.

From now on, you will be able to work in trucks equipped with ECU PLD/PLD2, MCM/MCM2, EMS S6, EMS S7, EMS S8, EMD1 and many more gasoline cars with engines 1.0 and 1.4 TFSI and their ECUs as MED17. 1.21, MED17.1.27, MED17.5.1, MED17.5.20 or even MED17.5.5.

Check out our full list now of ECUs StageX compatible with almost 1000 ECUs from all manufacturers and brands.

Join the StageX Plus revolution now!

THURSDAY, MAY 19, 2022

Easy DTC Removal from a Variety of MED17.1 ECUs

DTC simple solution with StageX

Starting with this update you will be able to easily remove DTCs in a variety of gasoline ECUs such as MED17.1, MED17.1.1, MED17.1.11, MED17.1.6, MED17.1.61, MED17.1.63 and MED17.1.65 This complements our latest release, which introduced highly accurate mappacks for those control units. From now on, you can perfect your modification from start to finish in the best possible way!

And remember, StageX Plus subscription includes all accurate Mappacks and DTC solutions and the new checksum calculation for your project at no extra charge!

FRIDAY, MAY 6, 2022

Trucks and TRW new batch of gasoline ECUs at stageX

The mappacks database continues to grow exponentially

Thanks to this update we bring you mappacks for over 50 more control units! The main feature is many mappacks for trucks with TRW ECU within the EMS2.X family and even more gasoline control units Bosch motors from the ME7 and MED17 families!

The increase in the number of new mappacks

Mappacks for engines Bosch gasoline control units expands even further, introducing now support on ME7.1 for 2.8 V6 engines, ME7.1.1 for 2.5 V6, 3.2 VR6 and 4.2 V8 engines, ME7.5 for 1.8T and 2.0 MPI engines, ME7.5.10 for 1.4 MPI engine, and many more variations of the MED17s, such as, for example, MED17.1 for 1.4 and 2.0 TFSI, MED17.1.1 for 2.0, 2.5, 4.0, 4.2 and 5.2 TFSI, MED17.1.11 for 3.8 FSI and 4.0 TFSI, MED17.5 and MED17.5.2 for 1.8/2.0 TFSI, MED17.5.3 for 1.8 TFSI and MED17.5.53 for 1.4 TFSI engine.

But that's not all!

Now you'll be able to work on even more trucks! TRW control units as EMS2, EMS2.2, EMS2.3 and EMS2.4 are fully covered by very detailed mappacks!

The stageX Revolution keeps accelerating

We are not forgetting either the user experience And starting with this update, we're introducing new, even more, surprising and engaging experiences.

Get ready to see many, many more exciting changes in upcoming updates!

Wednesday, April 13, 2022

Easy DTC removal for all Siemens/Continental ECUs

Complete solution with all switches for all Siemens/Continental Diesel ECUs.

Thanks to the simple solution of DTC correction will remove the necessary trouble codes after modification. This operation is facilitated by our full range of accurate mapping packages.

From now on, you can not only easily modify all the Siemens/Continental Diesel ECUs , thanks to our descriptive mapping packages, but also eliminate the entire range of possible DTCs with just a few clicks, finishing your work faster than ever! This includes the SID200, SID300 and 800 recently supported.

That's not all! We've also added support for Bosch MED17.5.21 for 1.0 TFSI and 1.4 TFSI gasoline engines and improved many algorithms of the currently supported ECUs, by including all the necessary switches.

New DTC removal algorithms

ECU FORD Diesel SIEMENS SID202
ECU MAZDA Diesel SIEMENS SID202
ECU VOLVO Diesel SIEMENS SID202
ECU FORD Diesel SIEMENS SID204
ECU JAGUAR Diesel SIEMENS SID204
ECU LAND ROVER Diesel SIEMENS SID204
ECU FORD Diesel SIEMENS SID206
ECU MAZDA Diesel SIEMENS SID206
ECU VOLVO Diesel SIEMENS SID206
ECU NISSAN Diesel SIEMENS SID301
ECU RENAULT Diesel SIEMENS SID301
ECU NISSAN Diesel SIEMENS SID303
ECU AUDI Diesel SIEMENS PPD1.X
ECU SEAT Diesel SIEMENS PPD1.X
ECU SKODA Diesel SIEMENS PPD1.X
ECU VOLKSWAGEN Diesel SIEMENS PPD1.X
ECU CITROEN Diesel SIEMENS SID801
ECU PEUGEOT Diesel SIEMENS SID801
ECU SUZUKI Diesel SIEMENS SID801
ECU CITROEN Diesel SIEMENS SID802
ECU FORD Diesel SIEMENS SID802
ECU CITROEN Diesel SIEMENS SID803
ECU FIAT Diesel SIEMENS SID803
ECU FORD Diesel SIEMENS SID803
ECU PEUGEOT Diesel SIEMENS SID803
ECU VOLVO Diesel SIEMENS SID803
ECU CITROEN Diesel SIEMENS SID804
ECU FORD Diesel SIEMENS SID804
ECU PEUGEOT Diesel SIEMENS SID804
ECU CITROEN Diesel SIEMENS SID807
ECU FORD Diesel SIEMENS SID807
ECU MAZDA Diesel SIEMENS SID807
ECU PEUGEOT Diesel SIEMENS SID807
ECU VOLVO Diesel SIEMENS SID807
ECU AUDI Petrol Bosch MED17.5.21 (1.0 TFSI / 1.4 TFSI ENGINE)
ECU SEAT Petrol Bosch MED17.5.21 (1.0 TFSI / 1.4 TFSI ENGINE)
ECU SKODA Petrol Bosch MED17.5.21 (1.0 TFSI / 1.4 TFSI ENGINE)
ECU VW Petrol Bosch MED17.5.21 (1.0 TFSI / 1.4 TFSI ENGINE).

THURSDAY, MARCH 31, 2022

Title: StageX, Siemens/Continenta diesel ECU launch

Even more ECUs in StageX

From now on, StageX is compatible with all Siemens/Continental control units for diesel engines. The new update also includes many iterations of the MED17.1 and MED17.5 gasoline ECUs . From now on, you can quickly work with an ever-increasing number of ECUs thanks to Magicmotorsport's remapping software.

StageX now works with all Siemens/Continental diesel engine control units.

Increase continued in the number of diesel ECUs compatible with StageX. As with the entire BOSCH ECU family, among many other brands that will soon have full coverage, all ECU remaining of Siemens/Continental have been added to the admitted list.

We would like to announce that you can now work in Siemens SID605, SID901, SID902, SID904, SID913 and SID914 quickly and efficiently with StageX Plus, where you can be sure that every description and axis matches reality and even if you want to do Stage 3, we've made it easier for you to correctly point out and describe all the necessary maps.

Map packages for gasoline engines

The new update also includes new gasoline ECUs. In this update, you can now work on many iterations of ECU MED17.1 and MED17.5 As we continue to expand the StageX map pack database, just to name a few: Bosch ECU MED17.1.6, MED17.1.61, MED17.1.63, MED17.1.65 and MED17.5.21 for 3.0T, 3.6FSI, 6.3 FSI, 1.0 TFSI, 6.0TFS.

FRIDAY, MARCH 18, 2022

New DTC removal for newly added ECUs

Support for many SID300, MED17.1 and more

The latest update of StageX Includes diagnostic trouble codes (DTCs) erasure for a number of newly supported ECUs, such as MED17.1 for 2.0TFSI, 4.0 TFSI and 6.0TFSI, MED7.5 for 1.8T and many SID300, DCM, CRD and DMCI. ECU.

With the easy DTC Clearance With StageX, you can select codes to delete in batches and delete them with a single click.

And, as always, StageX developers continue to push for full map and DTC coverage for all gasoline and diesel ECUs on the market, with just a few more updates to go before diesel ECUs are covered.

Stay tuned !

FRIDAY, MARCH 4, 2022

StageX continues to grow

Map packages for new and established gasoline and diesel engines.

StageX grows every month and this month is no different! Today we feature a variety of highly descriptive and well-polished map packages. They include modern and accurate solutions for New and established gasoline and diesel engines , giving you the widest variety of models available anywhere.

The latest update includes many ECUs for diesel engines such as SID2XX and SID3XX . There is also support for many gasoline engines with ME7.X and MED17.X for engines 2.7T, 1.8T, 2.5 TFSI, 4.0 TFSI either 6.0TFSI , as well as many new MG1CS models.

TUESDAY, FEBRUARY 22, 2022

Last chance to get special StageX pricing

Hurry! You have until April 4, 2022.

There are only a few more weeks left to take advantage of the Engine control unit (ECU and TCU) remapping software smartest and fastest on the market at our lowest price.

If you've already purchased StageX at the special price with automatic renewal, your cost will remain at €79.00 per month. If you subscribe before April 4, 2022, and choose automatic renewal, you can lock in the special price for as long as you like.

FRIDAY, FEBRUARY 18, 2022

Hundreds of additions to easily remove DTCs

Nearly 100 new ECUs with easy DTC removal

Gasoline or diesel - Bosch, Delphi, Continental or Siemens - MG1, SIMOS, SID or DCM - we aim to cover every ECU on the planet!

With StageX can now easily clear DTCs from nearly 100 new ECUs across the spectrum. A spectrum that includes EDC17 through DCM3 and SID200, right up to new MG1 and SIMOS ECUs—stay tuned! The number of supported ECUs is growing faster than ever.

Easy DTC removal added for newly supported SIMOS and MG1 ECUs!

All newly supported ECUs are now equipped with easy DTC clearing! This includes Continental ECUs from SIMOS8 to SIMOS16 and Bosch MG1 ECUs such as MG1CS001, MG1CS002, MG1CS008, MG1CS011, MG1CS047 and MG1CS111, and many more! The StageX expansion of DTC clearing additions continues to accelerate, so don’t hesitate. Join the StageX Plus revolution now!

See with your own eyes how easy it is to remove DTCs with StageX

Fast and secure national and international shipping

Increase the potential of your vehicles

A whole new world of additions

Here's what's new:

MEVD17 is just the beginning

Stay up to date with our endless innovations

New tickets for StageX

The StageX Christmas Festival is ramping up!

ADVANCE IN AI TUNING

AI SOLUTIONS ARE COMING TO TOWN

News under the Christmas tree.

Solutions for Denso and Transtron have arrived

Loading the 1500 map packs.

More than 1,500 ECUs supported

Next massive batch of fixes and map packs

Get ready for this season

Primavera StageX: More than 500 new solutions are ready for you

A shower of advantages

No time limits!

FREE Map Packs & DTC Removals!

33% off for Flex Masters!

Get your F7!

More than 10 reasons to be a StageXer

10 out of 10!

10 out of 10!

High-quality map packs!

New map packs, new fixes, increased limits!

Even more cars and trucks

Plus, another batch of qualitative maps for gasoline and diesel.

Great discounts and FREE solutions

New AI solutions and map packs coming soon

Plus, another batch of qualitative maps for gasoline and diesel.

No, that's not all! Newly crafted map pack menu

StageX will be more open than ever!

Don’t worry: StageX Editor will continue to expand with new features and possibilities!

Exclusive DTC clearing support for EMS2.4 and all Simos19.x ECUs

Ongoing promotions!

Five free solutions per day

The Revolution - Act II

Completely new AI solutions!

StageX 2.0

Special hint: The next batch of Mappacks

New FREE DEMO & SOLUTIONS

The StageX Academy is a reality

Clear DTCs in zero time!

Cars, tractors, and crawler loaders... what else?

DTC removal algorithms in StageX continue to improve.

Over 30 Amazing New ECUs in StageX!

New DTC removal algorithms for EMS2.3 and MED9.1

Summer is ending, but the map packs are endless.

Upcoming map packages: DENSO Diesel and Bosch Gasoline ECUs

StageX DTC Monthly Update

Next ME17.1 and ME17.5 DTC Clearance Algorithms

New StageX map package update covers over 60 new ECUs

This summer is coming explosively!

StageX continues to grow strong

Welcome Dark Mode

New ECUs from Temic, Continental, Motorola and Bosch now on StageX!

DTC simple solution with StageX

The mappacks database continues to grow exponentially

The increase in the number of new mappacks

The stageX Revolution keeps accelerating

Complete solution with all switches for all Siemens/Continental Diesel ECUs.

Even more ECUs in StageX

StageX now works with all Siemens/Continental diesel engine control units.

Map packages for gasoline engines

New DTC removal for newly added ECUs

Support for many SID300, MED17.1 and more

Map packages for new and established gasoline and diesel engines.

Hurry! You have until April 4, 2022.

Hundreds of additions to easily remove DTCs

Easy DTC removal added for newly supported SIMOS and MG1 ECUs!

See with your own eyes how easy it is to remove DTCs with StageX